MCP servercom.engscript/mcp

General mass/energy balance solver using GEKKO

Calculate thermodynamic properties of hydrocarbon mixture. Supports hydrocarbons and non-hydrocarbon chemicals (PR EOS flash calculation).

Calculate polytropic efficiency of compressor

Cooling tower capacity evaluation

Cooling tower capacity evaluation: design vs test

Cooling tower evaporation rate: mass removal rate (MR) and heat removal rate (QR)

Cooling tower L/G ratio calculation

Cooling tower NTU and characteristic C value calculation

Calculate gas control valve Cv and Kv from flow conditions

Calculate liquid control valve Cv and Kv from flow conditions

Calculate steam control valve Cv and Kv from flow conditions

Calculate boiler feed water flow and total flow from pressure and temperature reduction through desuperheater. Also returns the inlet/outlet/BFW specific enthalpies (h_in, h_out, h

Data Validation and Reconciliation

Economic analysis: NPV, IRR, Simple Payback, Profitability Index, EAC

Calculate CO2 emission conversion factor from gas composition

Calculate enthalpy of flue gas from composition

Generic formula calculator with unit conversion and IF-THEN-ELSE

Calculate MW, LHV and HHV of fuel gas from composition

Calculate depressurization gas volume and hold time for gaseous nitrogen storage vessel

Heat exchanger fouling resistance back-calculation from shell/tube-side operating conditions.

Calculate depressurization gas volume and hold time for high pressure air storage vessel

Calculate fired heater heat duty and efficiency from inlet/outlet conditions and composition

Calculate fired heater loss efficiency from ambient temperature, stack gas temperature and excess oxygen

Calculate LMTD of heat exchanger

Calculate depressurization gas volumn abd hold time and saturation temperature for liquid nitrogen storage vessel

Primary thermodynamic property calculator. Use this tool first for all mixture property calculations. Supports hydrocarbons and non-hydrocarbon chemicals (PR EOS flash calculation)

Convert mass flow rate to volumetric flow rate at standard condition

Gas orifice sizing / differential pressure / flow rate calculation based on ISO 5167 orifice. Exactly ONE of [M, dP, D2] must be set to '?' — that variable will be calculated.

Liquid orifice sizing / differential pressure / flow rate calculation based on ISO 5167 orifice. Exactly ONE of [M, dP, D2] must be set to '?' — that variable will be calculated.

Calculate compressed air pipe sizing: pipe diameter, velocity, pressure drop

Calculate Darcy friction factor based on Reynolds number and pipe roughness

Calculate isothermal gas pipe flow: density, volumetric flow rate, mass flow rate from pressure drop

Calculate liquid pipe flow: volumetric flow rate and mass flow rate from pressure drop

Calculate optimal pipe insulation thickness to limit outer surface temperature (burn protection) and minimise heat loss. Uses cylindrical heat conduction + external convection mode

Calculate nitrogen pipe sizing: pipe diameter, velocity, pressure drop

Calculate steam pipe sizing: pipe diameter, velocity, pressure drop

Calculate water pipe sizing: pipe diameter, velocity, pressure drop

Calculate required PSV (pressure safety valve) relief area for gas/vapor service per API 520

Calculate required PSV (pressure safety valve) relief area for liquid service per API 520

Calculate required PSV (pressure safety valve) relief area for steam service per API 520

Psychrometric properties of moist air

Calculate gas molar volume using equation of state

Calculate pump brake horsepower

Calculate mean pressure between inlet and outlet

Calculate refrigerant thermodynamic properties using CoolProp. Provide Fluid name and any 2 state variables from: T, P, rho, H, S, U. Returns all remaining properties: T, P, rho, H

Solve nonlinear equations with unknown variables using fsolve

Calculate thermodynamic and transport properties of steam based on IAPWS

Calculate flash steam flow from pressure reduction

Calculate steam leak mass flow and flow condition (CHOKED / SUBCRITICAL) based on upstream and downstream conditions

Calculate mass flow from pin-hole on the steam piping

Calculate multistage steam turbine isentropic efficiency

Calculate depressurization steam volumn and hold time for steam accumulator

Calculate steam turbine isentropic efficiency

Gas Venturi tube sizing / differential pressure / flow rate calculation based on ISO 5167 Venturi meter (as cast convergent venturi tube). Exactly ONE of [M, dP, D2] must be set to

Liquid Venturi tube sizing / differential pressure / flow rate calculation based on ISO 5167 Venturi meter (as cast convergent venturi tube). Exactly ONE of [M, dP, D2] must be set

Convert volumetric flow rate to mass flow rate at standard condition and normal condition Sm3/hr, Nm3/hr, SCFH

Advanced Data Validation and Reconciliation including gross error detection and elimation

Advanced Economic analysis with inflation, depreciation, and tax: NPV, IRR, Simple Payback, Profitability Index, NCF